Superflex® Sheeting

• Local manufacture
• Low carbon footprint
• Durable – dense smooth finish and proven performance in the market
• SANS 786 mark
• Composition 56% natural
• 100% recyclable
• Matching Welding Rod
• Group M Abrasion Rating
• Brand reputation – in the market for over 68 years
• The contrasting pattern is throughout the thickness
• Not directly dependent on ROE
• Phthalate-free
• No restricted substances 
• Class 1 Fire rating
• Continuity of supply
• Distribution capability – service level to market
• Direct delivery to site
• Representation (National footprint)
• NCS Coded
• 15-year warranty
• Technical support/back up

• Commercial
• Office
• Classrooms & Schools
• Hospitals
• Hospitality
• Leisure

Superflex® should be installed in accordance with manufacturer’s recommendations.

• Sub-floors must be smooth, hard, clean, and dry before laying commences.
• Uneven, solid or suspended timber floors may need preparation to meet the required standard.
• In case of direct to earth concrete, a damp proof membrane must be incorporated into the sub-floor.
• Superflex® sheeting and tiles must be allowed to relax for 24 hours in a uniform room temperature between 18°C and 27°C prior to installation.
• All sub-floors must be tested for moisture content prior to installation.
• The recommended adhesive for Superflex® sheeting and tiles is FloorworX No. 62 acrylic adhesive.
• Superflex® sheeting must be hot seam welded using FloorworX Welding rod.
• It is essential that during the course of installation the material be rolled in both directions with an articulated 68kg three section metal floor roller.

Superflex: Sheeting

Supply and fix 2.0mm / 2.5mm thick x 1.2m wide Superflex fully-flexible vinyl sheeting manufactured in accordance with SANS 786 and laid in FloorworX No. 62 acrylic adhesive which has been spread using a TKB-A2 notch trowel fitted at a rate of between 5.5m² and 6.5m² per litre or FloorworX No.71 contact adhesive spread using a flat trowel, brush or paint roller at a rate of approximately 3,5m² per litre (single surface application), on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using a reliable Self-Leveller when required, including all cutting and waste. The sheeting must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive. Joins must be butted, grooved and heat welded using FloorworX Welding Rod, ensuring that the welding rod bonds to more than 70% of the sheet thickness. The newly laid floor must, after 48 hours, be cleaned (stripped) using FloorworX Stripper, scrubbed using a diluted solution of FloorworX Rinse and then coated (sealed) with 3 coats of FloorworX Sealer.

Superflex: Tiles

Supply and fix 2.0mm/2.5mm thick x 300mm x 300mm Superflex fully flexible vinyl tiles, manufactured in accordance with SANS 786 and laid in FloorworX No. 62 acrylic adhesive which has been spread using a trowel fitted with an A2 notched blade at a rate of between 5.5m² and 6.5m² per litre on a previously prepared Class 1 sub-floor in accordance with SANS 10070, using a reliable Self-Leveller when required, including all cutting and waste. The flooring must be rolled in both directions with an articulated 68kg three-sectional roller immediately after it has been laid into the adhesive. The newly laid floor must, after 48 hours, be stripped using FloorworX Stripper, scrubbed using a diluted solution of FloorworX Rinse and then sealed with 3 coats of FloorworX Sealer.

FloorworX offers a 15 year limited warranty, subject to our terms and conditions, against defective material provided that it is installed and maintained in accordance with our recommendations.

PLEASE NOTE: This product is for indoor use ONLY.

Please refer to Cleaning & Maintenance under Technical.

Cleaning and Maintenance of Coatable Vinyl Flooring

STANDARD STORAGE PRACTICE

If an installation is large and material has to be stored on site, the following precautions should be taken:

• Storage area must be secure and away from other trades
• Storage area should be clean, dry and environmentally stable (18 ºC – 23ºC)
• Sheeting rolls should stand upright
• No heavy material should be placed on top of rolls or stacked boxes

Please Note: Temperature variations, excess weight or an uneven floor surface will distort the floor material. For more information please contact the FloorworX Technical Department by sending your query to technical@floorworx.co.za